Universal fittings are copper tube size products (CTS) used in hot and cold potable water distribution systems in residential, marine, and RV applications. All sizes listed are nominal, which are approximately the same as the inside diameter (I.D.). The outside diameter (O.D.) of CTS tubing is the nominal size plus 1/8".

 

  • Avoid installation where product will be exposed to excessive sunlight.
  • Universal fittings:
    • Leak-proof mechanical joints
    • Hand-tighten only
    • Connect to copper, CPVC, and other copper tube size products
    • Note the order in which each of the component parts are installed. Be sure all parts are present in this order before installing.

 

Universal Fittings

Universal Fittings:

  • Meets ASTM D3309
  • 200 PSI @ 73°F & 100 PSI @ 180°F
  • NSF Listed

 

Nominal Size
1/4" 3/8" 1/2" 3/4"
Outside Diameter
3/8" 1/2" 5/8" 7/8"

PRODUCTS

Designed to join PEX, copper, or CPVC tubing.

Coupling

Designed to join PEX, copper, or CPVC tubing.

Part #
Size Pkg Qty
Box Qty
Box Weight
541031 1/4" (C)
5 1
541051 1/2" (C)
5 1
54105 1/2" 10 20 2
541071 3/4" (C)
5 1
54107 3/4" 10 20 3
Designed to join PEX, copper, or CPVC tubing.

Reducing Coupling

Designed to join PEX, copper, or CPVC tubing.

Part #
Size Pkg Qty
Box Qty
Box Weight
541531 1/2" x 1/4" (C)
5 1
54153 1/2" x 1/4"
10 20 2
Designed to adapt from metal male pipe thread to PEX, copper, or CPVC tubing. Hand tighten only!

Special Female Adapter (FIP)

Designed to adapt from metal male pipe thread to PEX, copper, or CPVC tubing.

Hand tighten only! This fitting seals by means of a gasket and the use of joint compound or PTFE thread tape is neither necessary nor recommended.

Part #
Size Pkg Qty
Box Qty
Box Weight
543051 1/2" (C)
5 1
54305 1/2" 10 20 2
543071 3/4" (C)
5 1
54307 3/4" 10 20 2

Reducing Female Adapter

Designed to adapt from metal male pipe thread to PEX, copper, or CPVC tubing. Connects Water Softeners to in home plumbing supply.

Hand tighten only! This fitting seals by means of a gasket and the use of joint compound or PTFE thread tape is neither necessary nor recommended.

Part #
Size Pkg Qty
Box Qty
Box Weight
54310 1" x 3/4"
10 20 3
543101 1" x 3/4"
5 20 3
Designed to adapt from metal female pipe thread to PEX, copper, or CPVC tubing on the COLD WATER SIDE ONLY of a hot and cold water supply system

Male Adapter (MIP)

Designed to adapt from metal female pipe thread to PEX, copper, or CPVC tubing on the COLD WATER SIDE ONLY of a hot and cold water supply system. Where hot or changing temperatures are likely to be encountered, utilize a short metal nipple in conjunction with a Genova Universal Fitting Special Female Adapter. PTFE tape is the accepted method of sealing pipe threads or CPVC fittings. Do not use other materials or compounds unless specifically approved by the manufacturer.

Part #
Size Pkg Qty
Box Qty
Box Weight
544051 1/2" (C)
5 1
54405 1/2" 10 20 2
544071 3/4" (C)
5 1
54407 3/4" 10 20 2

90° Elbow

Used to change direction in piping and is designed to join PEX, copper, or CPVC tubing.

Part #
Size Pkg Qty
Box Qty
Box Weight
547051 1/2" (C)
5 1
54705 1/2" 10 20 3
547071 3/4" (C)
5 1
54707 3/4" 10 2

PVC to CPVC Bushing (IPS SPIGOT x CTS SLIP)

Used in COLD WATER APPLICATIONS ONLY to adapt from a PVC fitting socket to CPVC tubing.

Part #
Size Pkg Qty
Box Qty
Box Weight
55305 1/2" 10 200 4
55307 3/4" 10 200 5
55310 1" 10 100 4
55314 1 1/4"
5 25 2
55315 1 1/2"
5 25 2
55320 2" 5 25 3
Used to adapt to male pipe threads to CPVC tubing. A special elastomeric gasket ensures a leakproof seal.

Special Female Adapter (SLIP x FIP)

Used to adapt to male pipe threads to CPVC tubing. A special elastomeric gasket ensures a leakproof seal. Hand-tighten only! This fitting seals by means of a gasket.  The use of joint compound or PTFE tape is neither necessary or recommended.

Part #
Size Pkg Qty
Box Qty
Box Weight
50305 1/2" 20 500 17
50307 3/4" 10 250 11
50310 1" 10 100 9
Used to adapt female pipe threads to CPVC tubing in COLD WATER APPLICATIONS ONLY!

Male Adapter (MIP x SLIP)

Used to adapt female pipe threads to CPVC tubing in COLD WATER APPLICATIONS ONLY! Where hot water or changing water temperatures are likely to be encountered, utilize the recommended TRANSITION UNIONS. PTFE thread tape is the accepted method of sealing pipe threads on CPVC fittings. Do not use other materials or compounds unless specifically approved by the manufacturer.

Part #
Size Pkg Qty
Box Qty
Box Weight
50405 1/2" 20 500 12
50407 3/4" 10 250 12
50410 1" 10 100 7
50414 1 1/4"
10 50 5
50415 1 1/2"
10 50 8
50420 2" 5 25 9
50475 1/2" x 3/4"
10 250 9
Conveniently packaged in quantities of 10.

Male Adapter (MIP x SLIP) Contractor Pack

Conveniently packaged in quantities of 10.

Part #
Size Box Qty
Box Weight
50405CP 1/2" 50 11
50407CP 3/4" 25 12
Allows a direct 90º connection between 5/8” O.D. PEX, copper, or CPVC tubing and male running threads on faucet.

90° Swivel Elbow

Allows a direct 90º connection between 5/8” O.D. PEX, copper, or CPVC tubing and male running threads on faucet. Has a cone washer inside female end to achieve seal.

Hand tighten only! This fitting seals by means of a gasket and the use of joint compound or PTFE thread tape is neither necessary nor recommended.

Part #
Size Pkg Qty
Box Qty
Box Weight
54905 1/2" 10 20 3
This fitting is used to provide a branch from a main line and is designed to join to PEX, copper, or CPVC tubing.

Tee

This fitting is used to provide a branch from a main line and is designed to join to PEX, copper, or CPVC tubing.

Part #
Size Box Qty
Box Weight
545051 1/2" (C)
5 1
54505 1/2" 10 2
545071 3/4" (C)
5 2
54507 3/4" 10 3
Used to provide a branch from a main line and is designed to join PEX, copper, or CPVC tubing.

Reducing Tee

Used to provide a branch from a main line and is designed to join PEX, copper, or CPVC tubing.

Part #
Size Box Qty
Box Weight
54575 3/4" x 3/4" x 1/2"
10 3
The unique valve mechanically joins water supply tubing utilizing a special locking ring and elastomeric seal.

Line Valve

The unique valve mechanically joins water supply tubing utilizing a special locking ring and elastomeric seal. It can be used to join PEX, copper or CPVC tubing.

Part #
Size Box Qty
Box Weight
540051 1/2" (C)
5 2
54005 1/2" 10 3
540071 3/4" (C)
5 2
54007 3/4" 10 4
Adapts mechanically and is used where toilet, vanity or sink water supply piping comes through the floor.

Straight Supply Valve

Adapts mechanically and is used where toilet, vanity or sink water supply piping comes through the floor. Designed to join PEX, copper, or CPVC tubing.

Part #
Size Box Qty
Box Weight
530301 1/2" x 1/4" (C)
10 3
53030 1/2" x 1/4"
10 2
Adapts mechanically and is used where toilet, vanity or sink water supply piping comes through the wall.

Angle Supply Valve

Adapts mechanically and is used where toilet, vanity or sink water supply piping comes through the wall. Designed to join PEX, copper, or CPVC tubing.

Part #
Size Box Qty
Box Weight
530651 1/2" x 1/4" (C)
10 3
53065 1/2" x 1/4"
10 2
Mechanically joins ½” water supply piping to male pipe threads. A special elastomeric gasket ensures a leakproof seal.

Special Female Wing Elbow

Mechanically joins ½” water supply piping to male pipe threads. A special elastomeric gasket ensures a leakproof seal. Usually used for a shower arm connection.

Hand tighten only! This fitting seals by means of a gasket and the use of joint compound or PTFE thread tape is not necessary or recommended.

Part #
Size Pkg Qty
Box Qty
Box Weight
540551 1/2" (C)
5 1
54055 1/2" 10 20 3
Solvent welds directly onto ½" CPVC tubing and adapts mechanically to ³/8" O.D. Pex tubing or copper tubing.

Reducing Genogrip™ Adapter (SLIP x TUBING)

Solvent welds directly onto ½" CPVC tubing and adapts mechanically to ³/8" O.D. Pex tubing or copper tubing. Most often used to adapt from ½" CPVC tubing risers through floor ³/8" O.D. closet and/or lavatory riser tubes. Can also be used with metal risers.

Part #
Size Pkg Qty
Box Qty
Box Weight
530101 1/2" x 1/4" (C)
10 1
53010 1/2" x 1/4"
25 50 3
Solvent welds directly onto ½" CPVC tubing and adapts mechanically to ³/8" O.D. Pex tubing or copper tubing.

Genogrip™ Angle Adapter (SLIP x TUBING)

Solvent welds directly onto ½" CPVC tubing and adapts mechanically to ³/8" O.D. Pex tubing or copper tubing. Most often used to adapt from ½" CPVC tubing risers through floor ³/8" O.D. closet and/or lavatory riser tubes. Can also be used with metal risers.

Part #
Size Pkg Qty
Box Qty
Box Weight
53060 1/2" x 1/4"
10 50 3
These patented adapters solvent weld directly into standard fittings and adapt mechanically to both PEX tubing and copper tubing.

Genogrip™ Street Adapter (SPIGOT x TUBING)

These patented adapters solvent weld directly into standard fittings and adapt mechanically to both PEX tubing and copper tubing by utilizing a special metal gripper ring supplied with the fitting. These fittings can be used in conjunction with CPVC fittings to create an unlimited range of fittings to connect to any type of water supply tubing.

Part #
Size Pkg Qty
Box Qty
Box Weight
530751 1/2" (C)
10 2
53075 1/2" 25 2
530851 3/4" (C)
10 2
53085 3/4" 10 20 2

Submitting Form...

The server encountered an error.

Form received.

P    800–521–7488

F     8107441653

 

 

Genova Products, Inc. World Headquarters

7034 E Court St

Box 309

Davison, MI 48423-0309

Copyright 2016 Genova Products, Inc. All Rights reserved.

customer service icon
Designed to join PEX, copper, or CPVC tubing.
Designed to join PEX, copper, or CPVC tubing.
Designed to adapt from metal male pipe thread to PEX, copper, or CPVC tubing. Hand tighten only!
Designed to adapt from metal female pipe thread to PEX, copper, or CPVC tubing on the COLD WATER SIDE ONLY of a hot and cold water supply system
Used to adapt to male pipe threads to CPVC tubing. A special elastomeric gasket ensures a leakproof seal.
Used to adapt female pipe threads to CPVC tubing in COLD WATER APPLICATIONS ONLY!
Conveniently packaged in quantities of 10.
Allows a direct 90º connection between 5/8” O.D. PEX, copper, or CPVC tubing and male running threads on faucet.
This fitting is used to provide a branch from a main line and is designed to join to PEX, copper, or CPVC tubing.
Used to provide a branch from a main line and is designed to join PEX, copper, or CPVC tubing.
The unique valve mechanically joins water supply tubing utilizing a special locking ring and elastomeric seal.
Adapts mechanically and is used where toilet, vanity or sink water supply piping comes through the floor.
Adapts mechanically and is used where toilet, vanity or sink water supply piping comes through the wall.
Mechanically joins ½” water supply piping to male pipe threads. A special elastomeric gasket ensures a leakproof seal.
Solvent welds directly onto ½" CPVC tubing and adapts mechanically to ³/8" O.D. Pex tubing or copper tubing.
Solvent welds directly onto ½" CPVC tubing and adapts mechanically to ³/8" O.D. Pex tubing or copper tubing.
These patented adapters solvent weld directly into standard fittings and adapt mechanically to both PEX tubing and copper tubing.

P     800–521–7488

F     8107441653

 

 

Genova Products, Inc.

7034 E Court St

Box 309

Davison, MI 48423-0309

customer service icon
Designed to join PEX, copper, or CPVC tubing.
Designed to join PEX, copper, or CPVC tubing.
Designed to adapt from metal male pipe thread to PEX, copper, or CPVC tubing. Hand tighten only!
Designed to adapt from metal female pipe thread to PEX, copper, or CPVC tubing on the COLD WATER SIDE ONLY of a hot and cold water supply system
Used to adapt to male pipe threads to CPVC tubing. A special elastomeric gasket ensures a leakproof seal.
Used to adapt female pipe threads to CPVC tubing in COLD WATER APPLICATIONS ONLY!
Conveniently packaged in quantities of 10.
Allows a direct 90º connection between 5/8” O.D. PEX, copper, or CPVC tubing and male running threads on faucet.
This fitting is used to provide a branch from a main line and is designed to join to PEX, copper, or CPVC tubing.
Used to provide a branch from a main line and is designed to join PEX, copper, or CPVC tubing.
The unique valve mechanically joins water supply tubing utilizing a special locking ring and elastomeric seal.
Adapts mechanically and is used where toilet, vanity or sink water supply piping comes through the floor.
Adapts mechanically and is used where toilet, vanity or sink water supply piping comes through the wall.
Mechanically joins ½” water supply piping to male pipe threads. A special elastomeric gasket ensures a leakproof seal.
Solvent welds directly onto ½" CPVC tubing and adapts mechanically to ³/8" O.D. Pex tubing or copper tubing.
Solvent welds directly onto ½" CPVC tubing and adapts mechanically to ³/8" O.D. Pex tubing or copper tubing.
These patented adapters solvent weld directly into standard fittings and adapt mechanically to both PEX tubing and copper tubing.

inquiry@genovaproducts.com

P    800–521–7488

F    8107441653

Genova Products, Inc.

7034 E Court St

Box 309

Davison, MI 48423-0309

 

customer service icon